I made a Lexan plastic cover plate to be mounted onto the stock OEM dash around my relays area. This will help tuck in the wires and help shield them. I still need to paint this so it's in for just a test fitting for now while I figured out where to mount my aluminum "L" brackets and where best to secure it in with screws. I have small rectangular holes cut and filed out of the Lexan plastic cover plate to allow access to the heating, air conditioning buttons and the rear hatch popper. I think a lot of people who built these knight Rider replicas relocate those switches to somewhere more convenient. I may very well do the same thing, but for now this is a good way I figure to secure in some wires and help kind of panel off the underside of the Knight Rider dash a fair bit. This way it might make adding other goodies into those areas easier as they will have something more to be able to be mounted too. Just a thought anyways.
Showing posts with label knight rider 2 tv dash install. Show all posts
Showing posts with label knight rider 2 tv dash install. Show all posts
Friday, May 15, 2015
Lexan Dash Relays Area Cover Plate
I made a Lexan plastic cover plate to be mounted onto the stock OEM dash around my relays area. This will help tuck in the wires and help shield them. I still need to paint this so it's in for just a test fitting for now while I figured out where to mount my aluminum "L" brackets and where best to secure it in with screws. I have small rectangular holes cut and filed out of the Lexan plastic cover plate to allow access to the heating, air conditioning buttons and the rear hatch popper. I think a lot of people who built these knight Rider replicas relocate those switches to somewhere more convenient. I may very well do the same thing, but for now this is a good way I figure to secure in some wires and help kind of panel off the underside of the Knight Rider dash a fair bit. This way it might make adding other goodies into those areas easier as they will have something more to be able to be mounted too. Just a thought anyways.Sunday, May 3, 2015
Third Dash Test Fitting
Another test fitting today of my Knight Rider 2 TV Dash after trimming a little bit off of the drivers side mounting wing on the dash and sticking down the pipe insulation I ran across the front of the stock OEM dash. I drilled in a few holes and Zip-Tied down the pipe insulation to the OEM dash just to be doubly sure it not going anywhere. After letting the 3M glue dry overnight I also removed the masking tape from around the steering column that I had glued on a piece of the pipe insulation and a piece of high density foam rubber to help raise up the front of the Switch Pods to match the Gull-wing a lot better. I put the dash in for another test fitting and it's definitely fitting better after those tweaks. I think I can still trim a little more off of the mounting wing on the drivers side but I would not take off too much more though as it's fitting pretty good now. Although I did try and put my windshield side moulding back on the window column to see if that would fit, it doesn't so I'm not sure what others have done to rectify that. I do know now that I don't need so many power wires going up to the Upper Console when I can get away with either a 16 or 10 AWG wire to feed power to the upper console. This would minimize the amount of wires I currently have running up both sides of the window column. I can then run that power wire to my fuse block I have installed on the passenger side hush panel. That way both the Upper and Lower consoles will get their power from that block.
Once they fit nice I'll cut out a recessed area in the "Slats" of the speaker grills to allow for a countersunk screw in a few areas and then secure the speaker grills to the Knight Rider Dash. I'll probably clean them up and repaint them too before securing them in just so they will look a lot nicer.
2 TV Dash Installation Tweaks
After a lot of experimenting with ways to get the Knight Rider 2 TV Dash to fit perfectly I think I have a pretty good handle on it. Yesterday I tried this option using a long piece of foam pipe insulation I had kicking around. This is a 2" diameter split pipe insulation I got from Home Depot. For my test fitting I just simply taped it into position while I test fitted the dash again.
I noticed that with the pipe insulation in under the front of the dash that it raised up the front of the dash enough that turning the key in the ignition is much easier, it still rubs a little but my dash can also still go up another 1/4 inch approximately to light up the top of the Gull-Wing with the top of the Switch Pods this extra room should make the Ignition Key Collar clear the top part of the dash. I have even been informed that you can trim off the top part of the Ignition Key Collar that interferes with the dash if needed. I'll only resort to that if absolutely necessary.
I took two "Rubber Cups" square rubber blocks you can get from Canadian Tire or most furniture stores so as your furniture legs don't mark up your floors, I placed them close to the passenger side under the foam pipe insulation to give that part of the dash a little more height as it looked like it needed levelling up a bit to match my Switch Pods.
The drivers side of the dash needs to be pushed in more but I was noticing the the side mounting "Wing" was butting right up against the stock OEM dash so I needed to trim off a little of that. I figure about a good half inch by the looks of the picture (above right). So I trimmed of a little less than that to try it out and see if it makes a difference, if it does I'll file off a little more. I basically want to try and get the part of the dash that fits up close to the windshield in under that black masking or whatever it is that goes around the outer edge of the windshield. I think that is how it's supposed to fit.
Here are a few shots of yesterdays dash test fitting, it's really starting to come together and look really good. I still have a few minor tweaks to do like see how it looks now that I had put the "Rubber Cups" in under the pipe insulation close to the passenger side and see if that levelled out the dash that extra bit for the Switch Pods.
I'll be doing another test fitting to see how those tweaks look today. I had to leave my foam pipe insulation over night to let the 3M glue set that I stuck it down to the stock OEM dash with so today it should be fine for me to go ahead and see how my tweaks will work out. I also hooked up the Voice Box yesterday for a test, first time I have ever done that. If you watched my latest video you'll see that is working really well. K.I.T.T. is REALLY starting to come to life. :)
Friday, May 1, 2015
Second Dash Test Fitting - POWER!
Yesterday seeing how I now had all of the electronics installed into my Knight Rider 2 TV Dash I figured it was definitely time for another test fitting in the Trans Am. This time would be a powered test since I know for sure now that my dash gauge cluster wires are wired correctly to the plug. I was pretty sure they were as I had done it very carefully and spent a lot of time making sure that I had labeled each wire carefully. But even still, being new to all of this I had my minor doubts. Here you can see my dash resting upside down on the back of my car (left), in preparation to be test fitted into the car. For this test I would simply be getting my dash into as close a position as possible to see what sort of tweaks and adjustments I would need to do and I would only be hooking up the gauge cluster plug and my plug I had most recently made for my GPS and LCD screens.
Here you can see my dash test fitted into the car (above left & right). Tough to get it in and I can even feel that it will need to be shimmed up and adjusted in some ways. I had a very difficult time getting my Quick Release steering wheel adapter on so some tweaks will need to be done there. Also it was very difficult to get the key into the ignition to turn on the car so some adjusting will need to be done there too. I think I may need to adjust my steering column a little to one side to get it to align better with the top middle part of the Switch Pods.
Here you can see my dash turned on (left). I did notice that the power seemed to have an intermittent connection in my dash gauge cluster plug so I think during all of my out of the car test in my back room the plug connection must have gotten damaged a little. Those pins in the Molex connectors can be pretty delicate and I think when I had two just inserted in for power and ground and held in place with an Alligator clip that somehow the female end of the pin must have gotten inadvertently widened. So I'll need to either re-pin it or just snip the power and two ground connections from my gauge cluster plug and wire them up to a different plug. Most likely one of those more sturdier trailer hitch plugs as the pins in those are factory sealed and very durable. I have to admit if I could have found one of those that was a 10 or 20 pin connector I would have used a couple of those for my dash gauge cluster connections. Oh well, live and learn ;)
I thought also during my dash powered test fitting that one of my "Dummy" rows of LEDs were not working but after reviewing some of my very early dash start up tests I could see that the board always acts that way so I guess that's just the way that one board works.
Over all I was very happy with my latest test fitting even though I can see I have a good deal of adjusting to do to get the dash to fit just right. Being new to this hobby I'm not sure how a lot of the other Knight Rider car builders tackle these many issues so I'll be doing some research on that to see if I can get some helpful pointers and tips that I will pass on here.
Friday, April 10, 2015
Finishing The Dash Underside Cover Plate
The basic shaping of my dash underside cover plate is done, still needs a little work in some areas to refine it a little but I have it screwed into place for now. As I had mentioned in a previous post I'll hold off on the priming and painting until I have taken the whole dash out to the garage for another test fit in K.I.T.T. and have a closer look at what kind of space I have between the back part of my cover plate and the stock OEM dash to see about how I might approach the idea of extending the cover plate a little further so as it can be screwed into the stock OEM dash plastic. Then once that final fabrication is done then I can prime and paint it after a final test fitting. But for now in these pictures you can see what I have done.
I do know that some other people within the Knight Rider Community have done something similar to this but I can't recall who had done it and how they had approached their cover plate project. Now depending on who's dash once has and what season dash the process of making an under side cover plate will vary somewhat. This REALLY is a custom job. ;)
Thursday, April 9, 2015
A Few Modifications To My Dash Underside Cover Plate
I added a bit more of a "Tab" in the area of my cover plate close to where the monitors are located on the dash, reason being that I needed a bit more in that area in order to be able to place a mounting screw into one of the "L" brackets I have installed that the electronics are attached too. For me this is a great place to help secure the dash under side cover plate.
Next step was to cut out an additional aluminum "L" bracket the the tapered end of my underside cover plate to be also secured to the dash with a screw. After cutting the aluminum I drilled in some holes to allow more of the fibreglass and resin to seep in and grip more to the dash. Here on the left image you can see the aluminum "L" bracket glued into place with some Contact Cement.
On the right you can see the "L" bracket finally glassed into place with fibreglass resin and matting. Once fully set I'll place my cover plate into position and tape it down with some masking tape just to hold it in place while I drill the holes for the mounting screws. Once the holes are drilled I can smooth out the cover plate a little more and then it's basically done. I'll hold off on the priming and additional sanding before painting as I may very well want to add more to the cover plate that fits close to the stock OEM dash. I'll know a lot more about how much and what needs to be done in that area after I get around to doing another test fitting of the dash in the car. It's no doubt going to be a little tricky and finicky work but no much so that making this cover plate to begin with. Just takes a little patience and perseverance. ;)
Monday, September 29, 2014
Switch Pod Buttons Arrive From KRW
Yayyy... the Switch Pod switches along with the extra buttons set arrived in the mail today from Knight Rider World. Now I can install these into my switch pods, then do another test fit of the dash so I can make sure my switch pods get mounted on in the right position, then I can glass them onto the dash.
I noticed that on the switches boards there are no mounting holes so I'm not sure how these get mounted into the pods. I'm sure I'll figure a way. Maybe cut a hole big enough for the switches to poke through the face of the pods and then use the edge of the boards as a stop or brace and then secure something over top of them inside of the back of the pods to secure them in place.... Hmmmm... going to require a little thought on that. I'm wondering how others have done this with their pod switches installation. Also need to figure out the wiring for these too. The red and black are obvious and I think the white is for the DTMF tones.
On an additional note I wonder how you can make each button do something different? That I would not mind figuring out just so I can solder on the necessary wires and run them through the pod to the back of the dash and label them for easy identification later.... that's if that is possible with this button set that is??
I noticed that on the switches boards there are no mounting holes so I'm not sure how these get mounted into the pods. I'm sure I'll figure a way. Maybe cut a hole big enough for the switches to poke through the face of the pods and then use the edge of the boards as a stop or brace and then secure something over top of them inside of the back of the pods to secure them in place.... Hmmmm... going to require a little thought on that. I'm wondering how others have done this with their pod switches installation. Also need to figure out the wiring for these too. The red and black are obvious and I think the white is for the DTMF tones.
On an additional note I wonder how you can make each button do something different? That I would not mind figuring out just so I can solder on the necessary wires and run them through the pod to the back of the dash and label them for easy identification later.... that's if that is possible with this button set that is??
Monday, September 15, 2014
V.B. Wiring Dilemas ???
I'm in the very delicate stage of wiring up my dash electronics. Now one has to keep in mind that I am NOT an electrician, I have had very little knowledge of electronics outside of ripping apart old TV sets, VCRs, DVDs and various other bits of electronics for scrap to be used in some weird "Cyber-Sculpture" I used to do and still do on occasion. I know how to solder wires and I can follow instruction if they are clear enough and make sense to me. Simple wiring diagrams like the two pictured above are good examples, these make sense to me. Although when I look at the two diagrams they do give me some confusion as to how they jive together, some of the connections I clearly understand and some I'm a we bit fuzzy on.... I'll try to explain ;)
The first diagram focuses on the wiring of the P.A.N.P. (Power, Auto, Normal, Pursuit) switches. Now by itself it makes perfect sense to me, No problem. Even the second diagram on the right for the V.B. (Voicebox) wiring by itself makes perfect sense to me. Now my issue is when I try to figure out how they jive together.
On the P.A.N.P. wiring scheme (left) the V.B. shows two power wires (+)
Now on the V.B. wiring scheme (right) the diagram shows a single power wire (+)
This power wire seems to run the lamps for both the Countdown indicators and the P.A.N.P. switch lamps. Now as I say in the diagram on the left for the P.A.N.P. wiring it shows two (+) positive wires that appear to connect together, if I'm understanding that correctly???
Now what I'm wondering is:
Do those two wires V.B. (+) and (+) simply get connected together into one wire that runs both the lamps for the Countdowns and P.A.N.P. switch lamps??
Here is a video where I also try to explain my dilemma. Please ignore the red wire connections from the ANP (Auto, Normal, Pursuit) to the NO (Normally Open) switch terminals, they should be black and I have since changed them to black... my bad.
NOTE: This Voicebox controls the P.A.N.P. switches. The top diagram on the left for the P.A.N.P. to Voicebox wiring I redid based on the lower resolution image that was kind of hard to make out some of the details. I have been told it is correct and accurate.
Tuesday, September 2, 2014
PANP Switches Have Arrived
I love getting packages in the mail from Knight Rider World. Today was the much needed PANP switches fro my 2 TV Knight Rider Dash. Now apart from the LCD monitors we pretty much have all of the dash electronics. I should now be able to wire up the electronics, run my wire loom with the connectors to my dash and finally see my dash in action. There are some things I need to do like install K.I.T.T.s Voice Box, bezel and Countdown Indicators as well as install these PANP switches after I secure in the mounting plate and bezel for them. I so can't way to see this baby all lit up ;) I'll need to test the electronics also just to make sure I do not have any bad boards, they traveled all the way from Italy and have not yet been tested since I got them so I'm going on a lot of faith that they are all OK. One thing I need to look into is how people are testing their dashes before installing them into their cars. At this point I am not sure if they use any type of special equipment or if they simply hook up the the car battery and Bob's yur Uncle ;)
Thursday, June 12, 2014
Air Ventilation Duct Re-routing
I picked up some one inch diameter flex hose in order to do some duct re-routing in my K.I.T.T. for the new Knight Rider 2 TV dash. Oddly enough Canadian Tire sells the one inch flex tubing but none of the accessories like couplers or dash vents so I had to get a little creative with some plumbing pieces and a piece of plastic from an old broken DVD player's casing.
I Had to cut a square 4 3/4" in diameter and cut a hole in the middle big enough to screw in the plumbing pipe elbow that I would attach my flex hose onto using a Zip Tie. I screwed the plastic cover I made onto the original OEM dash with some automotive screws, the kind with the washer already attached at the head of the screw. I thought that perhaps I might need to add some thin high density foam rubber onto the back of my mounting plate but as it turned out the fit was more than good enough to not need to. You can if you find your fit is not flush with the dash, but in my case it was a perfect fit so it will re direct the air flow really well into the flex hose that I will re-route to a coupler I will attach to after market dash vents I can pick up from Classics Auto.
Below is a couple of pictures of the plumbing parts I picked up and my custom mounting plate I made from plastic from a broken DVD player's casing.
Thursday, May 22, 2014
Voice Box Bezel Arrives
Yayyyyy. My K.I.T.T. voice box bezel has arrived from Knight Rider World. Awesome! So now I'll be able to get that and my VB module installed into the two TV dash soon. I just need to get some other projects done and out of my back work room first. ;-)
I am very pleased with the quality of this VB bezel, it's solid very sturdy construction and the overlays are colourful and very well made. I can't wait to see how this will look along with my VB module that I also got from Knight Rider World.
Sunday, April 20, 2014
Dash Cutting
Working on cutting out the dash plastic. I did some delicate cutting out around the area I had marked out and found I needed to cut a little more. I gained a little more wire slack on that lower white dash cluster connector, not much but a little. I'm going to experiment a little on the connectors pulled from the parts car and see if I can devise a crafty way of connecting directly to the copper tabs on those connectors. I have a few ideas, one of which is to make a special "Long Spade" style connector using some stock copper that I can cut and attach a ring connector to and then cover that with a wire cover something similar to heat shrink tubing. If my plan works ands the connections are solid enough, by that I mean able to withstand any shock the car will naturally be succumbed to during and kind of driving, then I may go with that method. My other option is to cap off any wires that are not needed and just butt connect longer wires that I will label and connect to a 20 pin Male / Female connector to the dash electronics.... we'll see. ;)
Subscribe to:
Posts (Atom)












