Saturday, September 10, 2016
Thursday, September 8, 2016
5 Inch LCD Touch Screens Installed Into Frames
I have installed the 5 inch touch screens into the monitor frames I got from Knight Rider World. I think because my 5 Inch screens were a little different than the ones that KRW uses I had to make a few modifications on how I attached all of the electronics to the back part of the frames. It took me the better part of this morning to figure out a good way to secure the boards to the back of the frames. I didn't have any circuit board spacers on hand so I used some plastic rigid tubing I had that I cut into short lengths and slipped over top of my long bolts that I used to secure the circuit boards to the back plate of the monitor frames. They seem to be pretty solid so unless they break I think they should be OK for now.
After I finished I soldered up the female end of the power connectors and then with fingers crossed I plugged them into my 12 Volt power supply pack. They started up OK so that is good, no shorts in the wiring. Hopefully I have enough separation between the circuit boards to allow for good air flow. I'm not sure how warm the boards will get if the monitors are on for any great deal of time, that is something to test out of the car for sure is a good endurance test of the monitor's electronics. I think they should be OK though. Next will be to test them out with the Knight O.S.Monday, September 5, 2016
Knight O.S. Surveillance Mode Module Installed
I installed the Knight O.S. Surveillance mode module just under where I have my Voice Projection button & Knight Rider Theme cut off buttons installed. I hooked it up to our Knight O.S. via my Mac book.... gotta use that until I find a suitable P.C. to use in the car.... rough but it gives you an idea of what is supposed to happen, My Dash is out while I'm working on installing the new monitor frames for the 5 inch LCD touch screens..... over all it's coming together though.... keep a look out for a video demo coming up soon.
Sunday, June 5, 2016
Installing the P.I.R. Sensors Into K.I.T.T's Front Nose
I installed the two P.I.R. Motion Sensors into K.I.T.T's front nose by mounting them onto the Fog Lights assembly. I made a couple of "L" shaped brackets for the P.I.R. sensors that I have installed into small project boxes. Each of the Fresnel Lens Domes on each P.I.R. Sensor has been sealed around the edge with black silicone, the same with the connector plug at the back of the box with the Power, Ground and Signal wires. The project boxes were then mounted to the "L" shaped brackets which were in turn mounted onto the Fog Lights assembly.
While I had my front nose off I had remembered that my Fog Lights look like they could come down a little, more the centre two, probably by about a good half inch or so... that will be something to tackle while I have the whole front end all "Discombobulated" ;) I'm happy the P.I.R. sensors are installed... just need to be wired up to our Knight O.S. and then all will be good and ready for another testing. I REALLY wish those P.I.R. Sensors worked through smoked glass or plexiglass that was smoked then they would not stand out so much.... Oh well we work with what we have I guess.... but hey if anyone knows of a P.I.R. sensor capable of that I'd love to hear about it ;)
Tuesday, May 31, 2016
One More tweak to The Login Screen
I made one more change to the log in screen buttons, I liked the idea of having some variety in the way that the log in code can be made a little more complex without being too complex, if that makes sense ;) I also came across this Keypad on eBay that can easily be used with Arduino and hence ultimately our Knight O.S. Software too. So I added in the A B C D buttons to allow for the use of those character entries also.
Sunday, May 29, 2016
Rear PIR Sensor Mounting Bracket
I was trying to figure out a good place to install the rear PIR sensor without making it too visible. One of my first thought on the idea was to install the sensor in the rear bumper just above the licence plate area, the only thing about that idea I didn't like was that I would have needed to drill a hole in the bumper and mount the sensor box in behind the hole with the white fresnel dome poking through the bumper. With it being white I felt it would stand out too much even though it would be a pretty clean install method I just did not like the idea of this "White Spot" on K.I.T.T.'s nice black bumper, so what to do? My 2nd thought was to perhaps make some sort of bracket that the sensor could be attached too and have it installed a little more out of sight under the rear bumper. So I made this aluminum bracket I will test out and see if it works well in that location. A little experimenting will be no doubt in order but if it catches infrared motion fine there then all good as the sensor will be a little more less noticeable.
Friday, May 27, 2016
New login Buttons
I made a series of new buttons for the log in screen seeing how the monitors are only 5 inch touch screens and the small Space Matt buttons I was using before might well have been a little on the small side for anyone who has "sausage fingers." ;) This new set of buttons is more the classic phone type key pad style of buttons, the beep SFX is still the same just the buttons have changed to make the log in screen a lot more user friendly.
Subscribe to:
Posts (Atom)










